S02-27 参数账本
18 条原始记录,数值及单位保留源文件精度。
| 参数与定位 | 数值及单位 | 来源与用途 |
|---|---|---|
target_TS02-27 · 1 | 298.14999999999998 K | 来源性质或假设 research target: inherited 25degC ambient, NOT an OEM measured inlet requirement 源或定义 report-data.Mission.selected.input_settings.ambient_T_K |
inlet_gauge_pressureS02-27 · 2 | 0.90000000000000002 bar(g) | 来源性质或假设 IE manual nominal, inherited frozen R2 input; pressure-drop qualification pending 源或定义 r2-integration.json fuel_supply.IE_inlet_pressure_gauge_bar.nominal |
ambient_pressureS02-27 · 3 | 101325 Pa | 来源性质或假设 inherited reference atmosphere 源或定义 report-data selected input_settings.base_pressure_Pa |
bar_to_PaS02-27 · 4 | 100000 Pa/bar | 来源性质或假设 exact unit conversion 源或定义 SI unit definition |
target_absolute_pressureS02-27 · 5 | 191325 Pa | 来源性质或假设 derived ambient plus nominal gauge pressure 源或定义 Pambient+Pgauge*bar_to_Pa |
target_densityS02-27 · 6 | 0.15541022991179504 kg/m3 | 来源性质或假设 native normal-H2 EOS result, not an independent measurement 源或定义 fzero(pEOS(Ttarget,rho)-Ptarget) |
target_enthalpyS02-27 · 7 | 3932193.6500574378 J/kg | 来源性质或假设 native normal-H2 EOS result, same energy reference as tank 源或定义 r23.eos; Leachman2009 |
FC_net_efficiencyS02-27 · 8 | 0.5 1 | 来源性质或假设 inherited net electrical efficiency scenario 源或定义 report-data selected input_settings.eta_fc_bus |
H2_LHVS02-27 · 9 | 120000000 J/kg | 来源性质或假设 inherited lower heating value 源或定义 report-data selected input_settings.LHV_J_kg |
tank_recovery_capS02-27 · 10 | 50 W | 来源性质或假设 original tank-pressure support branch only, not external HX capacity 源或定义 all-engineering-parameters.csv CRYO.recovery_cap |
tank_recovery_fraction_capS02-27 · 11 | 0.050000000000000003 1 | 来源性质或假设 original cap relative to chemical-minus-net-power upper bound 源或定义 all-engineering-parameters.csv CRYO.recovery_fraction |
C05_HX_budgetS02-27 · 12 | 0.29999999999999999 kg | 来源性质或假设 hardware mass budget only; no UA/thermal-capacity evidence 源或定义 frozen CRYO-BUDGET-1.2.0 vessel.warming_HX_budget_kg |
startup_purge_H2S02-27 · 13 | 0.001 kg | 来源性质或假设 conditional 1g heating illustration; purge need not all pass through stack 源或定义 report-data selected input_settings.startup_vent_H2_kg |
startup_durationS02-27 · 14 | 60 s | 来源性质或假设 original startup interval, no startup thermal-inertia model 源或定义 report-data selected input_settings.startup_s |
seconds_per_hourS02-27 · 15 | 3600 s/h | 来源性质或假设 exact unit conversion 源或定义 unit definition |
target_density_root_TolXS02-27 · 16 | 9.9999999999999998e-13 kg/m3 | 来源性质或假设 numerical root setting, not physical accuracy 源或定义 supplement code |
prestate_pressure_check_toleranceS02-27 · 17 | 0.10000000000000001 Pa | 来源性质或假设 CSV round-trip/state-alignment check only 源或定义 supplement code |
integral_closure_relative_toleranceS02-27 · 18 | 1e-10 1 | 来源性质或假设 postprocessing integration check only 源或定义 supplement code |